Design and Prototype Development of a Mini-Electric Arc Furnace F.A. Oyawale, Ph.D.1 and D.O. Olawale, M.Sc.2 1 Department of Industrial and Prod. Engineering, University of Ibadan, Nigeria 2 Department of Mechanical Engineering, The Polytechnic, Ibadan, Nigeria 1E-mail: festwale@yahoo.com ABSTRACT Although information relating to the design and Electric arc furnaces (EAF) have the capabilities fabrication of an electric arc furnace of such a required for furnaces used for metallurgical small size as that fabricated through this research. An electric arc furnace was designed research, was not readily available in literature, and constructed to melt approximately 5kg of the available information relating to the giant steel/cast iron scraps, using locally produced sized electric arc furnaces were used as a guide Soderberg electrodes. Tests carried out showed in the design of this prototype. that it required about 60 minutes to heat up the furnace to the melting temperature of cast iron (1150C – 1400C). It took about 95 minutes to DESIGN THEORY AND CALCULATIONS melt the first charge of 2kg resulting in a melting rate of 21.05g/minute. The average electrode An electric arc furnace should have a powerful consumption rate was 0.0467cm/minute. A transformer, high thermal and electrical transformer efficiency of about 83% was also efficiency, and a lining made of high-grade achieved. refractory [Edneral, 1979]. (Keywords: electric arc furnace, melting rate, Shape and dimensions of the bath electrode consumption rate, transformer efficiency) The bath is usually conical-spherical with the INTRODUCTION banks inclined at an angle of 45 0. This form ensures quick melting. One tonne of molten In an EAF, electric arcs are used to provide heat steel occupies 0.145m 3. The mass ratio of slag for melting and for smelting. The few EAFs in for acid-lined furnaces may be taken equal to the study country (Nigeria) are located in the 0.03 – 0.04. [Edneral, 1979]. integrated steel plant, the Delta Steel Company, and other large industrial plants. They are so The diameter-to-depth ratio of the bath operating complicated in design and so expensive that by the basic process is usually taken as: even national universities cannot afford to buy prototypes for experimental purposes. D = 5H (1) EAFs have numerous advantages required in where D = bath diameter, and H = total depth of furnaces for metallurgical research. Such the bath. features include close temperature and heat control, accurate analysis of melt, definite metal In existing furnaces, the height (h1), of the 1 refining sequence, high thermal efficiency (as spherical portion is roughly /5 of the total bath high as 70%), and production of steel directly depth: from pig iron and steel scrap. h1 = 0.2H (2) The objective of this research work is to design and develop an electric arc furnace for melting and the depth of the conical portion: steel/cast iron scraps using locally available materials. h2 = 0.8H (3) The Pacific Journal of Science and Technology –12– http://www.akamaiuniversity.us/PJST.htm Volume 8. Number 1. May 2007 (Spring) UNIVERSITY OF IBADAN LIBRARY The total volume of the bath, Vb, is the sum of D1= Drc + S (11) the volumes of the truncated cone and that of the spherical segment. By virtue of the The thickness of the lining is found by thermal relationships given above: analysis from the condition that the furnace shell should not be heated above 2000C at the end of Vb = 0.0968 D3 (m3) (4) the furnace campaign. With the refractory lining δ mm thick, the furnace will have the following inside diameter of the shell: Dimensions of the reaction chamber Di.sh = Drc + 2 δ (12) The banks of a furnace are usually made 100 to 200 mm above the door sill level or the bath The steel shell varies in thickness and may surface, to ensure that the slag does not contact range from 1/4 inch (6mm) thick for small the brickwork or reach the joint between the wall furnaces and up to 11/4 in (32 mm) thick on 80 to blocks and banks. The diameter of the reaction 100 ton furnaces [Robiette, 1972]. chamber is: Transformer power and furnace productivity Drc = D + 200 (mm) (5) Table 1 contains some recommendations on It is recommended that the following relationship transformer power for furnaces of different size, be used in determining the height of the reaction which are based on experiences in many chamber (H1) [Edneral, 1979]: countries. H1= (0.04 - 0.6) Drc (6) By analogy with the existing furnaces (using Table 1), the transformer power may be taken as the lower value relating to large-capacity Pap (MVA). Noting the inevitable switching off of furnaces. the furnace during melting required to push the scrap from the banks, partial operation of the The camber of the roof (h3 ) is: furnace at a reduced voltage when the arcs are open and radiation of much heat onto the walls h3 = 0.15Dr (7) and roof, the average power consumed during the melting period can be found by using a factor where Dr is roughly taken 1000 mm wider than of 0.8 – 0.9: Drc. Pav = 0.8 Pap (KVA) (13) Dr= Drc + 1000 h3= 0.15 (Drc + 1000 ) (8) Useful power consumed during the melting period (power consumed for the melting proper) The total height of the roof above the bath level is represented as: is given as: Pu = Pav cos φηel (KW) (14) H2 = H1 + h3 (9) Voltage taps The recommended slope (S) for the inclination of the wall is roughly 10% of the height from the The upper voltage tap of the secondary voltage line of banks to roof skewbacks: for small furnaces can be selected by using the following empirical formulae [Edneral, 1979]: S H1 −100= For basic furnaces (10) 10 V = 153 PAP (15) The diameter of the reaction chamber at the level of the roof skewbacks (i.e. at the level of For acid furnaces: the upper edge of the furnace shell) is: V = 70 +153 PAP (16) The Pacific Journal of Science and Technology –13– http://www.akamaiuniversity.us/PJST.htm Volume 8. Number 1. May 2007 (Spring) UNIVERSITY OF IBADAN LIBRARY Table 1: Recommended Transformer Power for Furnaces of Different Sizes. Furnace Capacity (t) Transformer Power (MVA) for 25 50 75 100 150 200 250 400 Making Various Steels (i) Alloy steels 5-18 20-25 - 30-35 - 55-70 - - (ii) Carbon steels 18-22 28-32 30-45 40-50 45-60 60-80 90 120 Transformer power of super powerful furnaces of the future - 40 - 60 - 125 - 200 (Source: Electrometallurgy and Ferro-alloys, 1979) Electrode diameter where, m = mass to be melted (kg), The diameter of electrodes can be found by the c = specific heat capacity of metal to be melted formula: (KJ/Kg0C), 0 d 0.406I 2δ θ2 = melting point of the metal ( C), = 3 (cm) (17) K θ1 = room temperature (0C), and Where I = linear current, (A) L = latent heat of fusion of the metal P 103 I = ap , MATERIAL AND METHODS V max 3 The electric arc furnace comprises two δ = electrode resistivity at 5000C (for graphitized Soderbeg self baking electrodes (Afolabi, 2004); electrodes δ = 10 ohm. Mm2/m), and an electrode support and sliding mechanism; a tiltable crucible lined with refractory silica brick in K = coefficient (for graphitized electrodes K = 2.1 which melting takes place; the roof also lined W/cm2). with silica brick, which is removable for charging and for pouring; and the support frame which The diameter of electrodes can also be found by carries the other parts. The crucible and roof the allowable current density (A/cm2). were constructed using 4mm thick mild steel sheet. The furnace is shown schematically in Electrode spacing Figure 1 and pictorially in Figure 2. The recommended ratio of the electrode spacing The furnace is supplied at 50Hz using a tapped diameter to the bath diameter is 0.45 for small power transformer with a high current furnaces, 0.35 for medium sized and large secondary, the connections between the furnaces, and still lower for super powerful transformer and the electrodes is a length of furnaces (Edneral, 1979). flexible cable which allows the electrodes to be moved vertically and also for the complete roof Energy distribution assembly to be lifted and moved horizontally. The energy required for melting of metal scrap is Melting is achieved by the heat generated by the electric arc drawn between the electrodes tips Q = mc(θ - θ ) + mL (18) and the scrap metals. The transformer is oil 2 1 cooled. The Pacific Journal of Science and Technology –14– http://www.akamaiuniversity.us/PJST.htm Volume 8. Number 1. May 2007 (Spring) UNIVERSITY OF IBADAN LIBRARY Table 2: Test Data. 1 2 1 2 102 1.0 3.0 2 2 89 1.0 3.0 3 2 94 1.0 3.0 4 3 128 2.0 4.0 5 3 130 2.0 4.0 6 3 123 2.0 4.0 Figure 1: Schematic of the Electric Arc Furnace. Vp= 220V, Vo= 62V, Ip= 30.5A, Io= 90A Soderberg electrodes Table 2: Average Melting Rate and Electrode Consumption. Melting Chamber Oil-Cooled Transformer 2 95 4.0 1:3 21.05 0.042 83 1150- 1400 Figure 1: Prototype Electric Arc Furnace. 3 127 6.0 1;2 23.62 0.047 83 1150- 1400 RESULTS AND DISCUSSION It took about 95 minutes to melt the first charge Tests were carried out on the EAF to assess its of 2kg resulting in a melting rate of operation and evaluate its performance. Table 2 21.05g/minute. A higher melting rate of and Table 3 show the test results. The EAF 23.62g/minute was however achieved when the performance was evaluated in terms of heating charge was increased to 3kg. The average total and melting rate, transformer efficiency, electrode consumption rate was Soderberg electrode consumption rate, and 0.0467cm/minute in the ratio 1:1.5 a transformer insulation resulting. efficiency of about 83% was also achieved. The refractory material used also showed high The result shows that it required about 60 insulation and thermal stability. Throughout the minutes to heat up the furnace to the melting tests, no crack was observed in the refractory point of cast iron (1150oC – 1400oC). lining. The Pacific Journal of Science and Technology –15– http://www.akamaiuniversity.us/PJST.htm Volume 8. Number 1. May 2007 (Spring) UNIVERSITY OF IB Mass of charge (Kg) AD Average time of melting (min.) A Test Average total electrode Mass of charge consumption (cm) N (kg) Electrode Consumption ratio LIB Time of Operation (min) Average melting rate (g/min) RA Average electrode consumption Electrode rate, (cm/min.) RY Consumption (cm) Transformer efficiency, η Melting temperature (C) CONCLUSION 8. Robiette, A.G.E. 1972. Electric Melting Practice. Griffin: London. 1-95. An electric arc furnace has been produced capable of producing small quantities of melted 9. Robiette, A.G.E. 1973. Electric Smelting steel for research. The tests show that the Processes. Griffin: London. 1-67. performance is satisfactory. The heating rate, 10. Shigley and Mischke. 1992. Mechanical melting rate, and electrode consumption rate are Engineering Design, International Edition. comparable to existing standard furnaces McGraw-Hill, Inc.: Singapore. 1-15. attaining a temperature of well over 1000 C within an hour and melting the first charge in about 95 minutes. ABOUT THE AUTHORS Tests carried out with Soderberg electrodes F.A. Oyawale, Ph.D., MNSE, Reg COREN, specifically produced locally for this project gave MNIIE is a lecturer in Industrial and satisfactory performance thus allaying fears of Manufacturing Engineering in the Faculty of inadequate electrode supply. Technology, University of Ibadan. His research interests include local substitution, renewable energy, and welding. RECOMMENDATIONS D.O. Olawale, M.Sc. is a lecturer in the Based on the study carried out in this project, Department of Mechanical Engineering at The there is a need to produce an effective and Polytechnic, Ibadan. His research interest is in efficient furnace transformer in Nigeria which the area of welding. can withstand the high current surges normally experienced in the operation. SUGGESTED CITATION Oyawale, F.A. and D.O. Olawale. 2007. “Design REFERENCES and Prototype Development of a Mini-Electric Arc Furnace”. Pacific Journal of Science and 1. Afolabi, A.A. 2004. “Production of Soderberg Technology. 8(1):12-16. Electrodes for Electric Arc Furnaces using Locally Available Raw Materials”. Unpublished M.Sc. Project, Industrial and Production Engineering Department, University of Ibadan. Pacific Journal of Science and Technology 2. Barber, H.1983. Electroheat. Granada Publishing LTD.:London. 88-92, 216-222. 3. Beddoes, J. and Bibby, M.J. 1999. Principles of Metal Manufacturing Processes. Arnold Publishers: London. 1-16. 4. Edneral, F.P. 1979. Electrometallurgy of Steel and Ferro-alloys. MIR Publishers: Moscow. 1-87. 5. Khanna, O.P. 1981. A Textbook of Material Science and Metallurgy (for engineering students). Dhanpat Rai Publications LTD.: New Delhi. 1-8,452-516. 6. Khanna, O.P. 1996. A Textbook of Foundry Technology (for Engineering students). Dhanpat Rai Publications LTD.: New Delhi. 7. Olawale, D.O. 2004. “Design and Construction of an Electric Arc Furnace”. Unpublished Masters Thesis, Department of Industrial & Production Engineering, University of Ibadan. The Pacific Journal of Science and Technology –16– http://www.akamaiuniversity.us/PJST.htm Volume 8. Number 1. May 2007 (Spring) UNIVERSITY OF IBADAN LIBRARY